It is too windy to work on a roof when the mean wind speed at roof level reaches 23 mph (37 km/h) or gusts reach 35 mph (56 km/h). NFRC guidance says slating, tiling and underlay work should then stop. Rolls of underlay need extreme care from 17 mph, gusting 26 mph.
The same NFRC guidance warns that gusts can be 50 to 100 per cent stronger than the mean wind speed (section 6.5), and the Health and Safety Executive says winds above 23 mph (Force 5) will affect a person’s balance.
When Is It Too Windy to Work on a Roof?
It is too windy to work on a pitched roof once the mean wind speed at the place of work reaches 23 mph or gusts reach 35 mph, and lighter materials stop well before that. There is no single legal number. Regulation 4(3) of the Work at Height Regulations 2005 says work at height may only be carried out when the weather does not jeopardise the health or safety of the people doing it. The NFRC guidance is how the roofing trade turns that duty into numbers.
Three points from the NFRC document decide most calls on site:
- Mean and gust both count. Each limit has a mean figure and a gust figure. If either is reached, the task stops.
- Readings are taken where the work is. Wind at ground level is often much lower than at the eaves or ridge, so the guidance says readings must be taken at the actual place of work (section 5.2).
- Readings are averaged. A supervisor with a handheld anemometer takes at least two readings of 15 seconds or more and averages them (section 6.4).
HSE’s own advice is blunter: do not go on any roof in strong winds, particularly gusting winds.
What Is the Maximum Wind Speed for Roof Work? Limits by Task
The maximum wind speed for roof work is 23 mph mean (35 mph gusts) for slating and tiling, and 17 mph mean (26 mph gusts) for the lightest materials. The table adds what HSE and the CAA say about scaffolding, ladders and drones. Beaufort forces follow the NFRC comparison table.
| Task | Stop or extreme care at (mean / gust) | km/h (mean / gust) | Beaufort (mean) | Source |
|---|---|---|---|---|
| Laying or handling slates, tiles, battens and underlay | Stop at 23 mph / 35 mph | 37 / 56 | Force 5 | NFRC 3.3(a) |
| Handling rolls of underlay (felt) on a pitched roof | Extreme care at 17 mph / 26 mph | 27 / 42 | Force 4 | NFRC 3.3(b) |
| Flat roof reinforced bitumen membranes (torch-on felt) and hot bitumen | Stop at 23 / 35 mph; extreme care at 17 / 26 mph | 37 / 56; 27 / 42 | Force 5; Force 4 | NFRC 3.4 |
| Liquid-applied waterproofing | Stop at 17 mph / 26 mph | 27 / 42 | Force 4 | NFRC 3.7 |
| Rigid insulation boards | Stop once hard to handle, possibly below 17 mph | Below 27 | Force 4 or lower | NFRC 3.8 |
| Plywood or OSB decking panels | Do not lay at 23 mph / 35 mph | 37 / 56 | Force 5 | NFRC 3.6 |
| Any fixing work on the roof | None in progress at Force 6 (25 to 31 mph mean) | 40 to 50 | Force 6 | NFRC Table 2 |
| Scaffolding and sheeting | No single figure; set by the design, checked after high winds | Not fixed | Not fixed | HSE scaffolds |
| Ladders and roof ladders | No wind figure; low-risk, short jobs only | Not fixed | Not fixed | HSE ladders |
| Inspections from the ground or by drone | No roof access; do not fly if wind could affect the flight | Set by the drone’s limits | Not fixed | CAA Drone Code |
The bigger and lighter the item, the lower the limit, because it catches the wind like a sail. The NFRC puts the wind load on a 2.4 m by 1.2 m plywood sheet at 31 mph at roughly 38 kg. It also says unfixed material must be secured and never left unattended, and suggests two-person lifts in wind.
What Wind Speed Stops Scaffolders?
There is no fixed wind speed that stops scaffolders in the UK; the limit comes from the scaffold’s design and the contractor’s risk assessment under Regulation 4(3) of the Work at Height Regulations. HSE requires a scaffold to be built to a recognised standard configuration, such as NASC TG20 for tube and fitting or the manufacturer’s instructions for system scaffold, or else designed by calculation.
Two parts of the HSE scaffolding guidance matter in windy weather:
- The client has to tell the scaffold contractor at the design stage whether sheeting, netting or brick guards are needed, because they change the loads the scaffold must carry.
- A scaffold must be checked whenever it is substantially altered or adversely affected, for example by high winds.
After a windy night, expect the scaffold to be checked before anyone climbs it. If you are wondering whether your job needs scaffold at all, our guide to working on a roof without scaffolding explains when ladders or a tower are acceptable.
Can Roofers Work in Light Wind or Gusts?
Yes, roofers can work in light wind, but gusts decide the day more often than the average speed does. A forecast mean of 15 mph can carry gusts well above the 26 mph trigger for felt and liquid systems. NFRC section 5.4 says gusts can reach about one and a half times the mean in open, level country and as much as twice the mean in city centres.
The Beaufort descriptions in the NFRC guidance, which HSE reproduces in Health and safety in roof work (HSG33), are a useful way to read the wind from your own window:
- Force 4, moderate breeze (13 to 18 mph): raises dust and loose paper; small branches move. Special care with materials over 5 m long and with lightweight insulation.
- Force 5, fresh breeze (19 to 24 mph): small trees in leaf begin to sway. Special care in all roof work; the mean is approaching the point where work must stop.
- Force 6, strong breeze (25 to 31 mph): large branches in motion and umbrellas hard to use. No fixing work anywhere should be in progress.
Light-wind days still suit small jobs, such as a slipped slate repair or checking flashings, as long as gusts stay under the limits.
What Happens to a Half-Finished Roof in High Wind?
A half-finished roof should be made safe before the crew comes down: loose materials fixed or removed, and any opening covered so rain cannot get in. That is the practical meaning of the NFRC rule that unfixed material must be secured and never left unattended.
What making safe looks like depends on the stage the job has reached:
- Tiles or slates stripped, underlay not yet down: the opening is covered with weighted or battened sheeting so it cannot lift.
- Underlay down, battens on: underlay is fixed under battens so it cannot balloon, and stacks of tiles on the roof are reduced or brought down.
- Flat roof part-laid: the edge of the new membrane is sealed or weighted, and loose rolls and boards come off the roof.
For occupied houses on long re-roofs, HSG33 describes temporary roofs, which need a bespoke engineering design unless they are a pre-designed proprietary system. If a cover does come loose overnight and water gets in, our guides to emergency roof repair and a roof leaking in heavy rain explain what to do first.
How to Check the Wind Forecast for Roofing Work
To check the wind for roofing work, look at both the mean wind speed and the gust figure in the Met Office forecast for your postcode, then compare them with the limits for the task. The Met Office forecast guide explains that the gust value is the highest wind speed expected between the time shown and the next period, and strong winds are shown in bold from 29 mph (25 knots).
- Know what the numbers mean. The Met Office defines a gust as the maximum three-second average wind speed, and the mean as the average over ten minutes (how the Met Office measures wind).
- Remember the height. Forecast speeds are measured 10 m above the ground. The Royal Meteorological Society notes that at 2 m, wind may be only 50 to 70 per cent of those figures, which is why a calm-feeling garden can sit under a windy ridge.
- Look at the whole working day. NFRC section 6.6 points roofers to the Met Office forecast for up to five days ahead.
- Read any warning in full. Met Office weather warnings are yellow, amber or red based on likely impact and how confident forecasters are. A yellow wind warning can mean low impact with high confidence or high impact with low confidence, so read the detail.
- Accept the on-roof reading. The forecast is for planning. The decision on the day comes from readings taken at the place of work.
Wind and rain often arrive together. If the forecast shows both, our guide to whether roofers can work in the rain covers the wet-weather side.
Homeowner Checklist When Your Roofing Job Is Rescheduled for Wind
When a roofing job is put back because of wind, a few checks keep the house dry and the restart smooth:
- Ask what has been done to secure the roof and whether any section is covered rather than finished.
- Keep people and cars away from the area below the scaffold until the wind drops.
- Look at ceilings under the work area and in the loft after heavy rain, and report damp straight away.
- Do not climb the scaffold or ladders to check sheeting yourself; ask the contractor to come back.
- Expect the scaffold to be checked before work restarts, as HSE requires after high winds.
- Agree the next likely working day based on the forecast gusts, not only the mean.
Wind Damage After a Storm: What Counts as a Storm for Insurance
For most UK home insurance, a storm means wind gusts of at least 55 mph (89 km/h), equivalent to Force 10 on the Beaufort scale. That is the Association of British Insurers description, which also covers rainfall of at least 25 mm an hour, snow of at least 30 cm in 24 hours, or hail that damages hard surfaces or breaks glass. Insurers check conditions using Met Office and other weather data.
In disputes, the Financial Ombudsman Service asks whether there were storm conditions, whether the damage is consistent with a storm, and whether the storm was the main cause. In one published decision (DRN-5253224) the ombudsman also noted that the Beaufort scale describes slight structural damage from 47 mph, so thresholds are not always applied strictly.
Fixing work on a roof stops at Force 6 (25 to 31 mph), far below the 55 mph storm level, so a job can be called off on a day that is nowhere near a storm. If your roof has lifted tiles, slipped slates or loose ridge after high winds, our storm damage roof guide explains what to record for a claim, our roof tile replacement cost guide gives typical prices, and a drone roof survey can show the damage without anyone going up while it is still gusty.
Windy Roofs in SouthWest London: Terraces, Stacks, Mansards and Flat Roofs
In SouthWest London, wind at roof level is often gustier than the forecast suggests because buildings disturb the airflow. NFRC section 5.3 lists what surrounding buildings can do: add wind pressure, add suction, create gusts higher than normal and cause eddies. Section 5.4 puts city-centre gusts at as much as twice the mean.
That matters for house types common across Balham, Clapham, Wandsworth, Streatham and Tooting:
- Victorian and Edwardian terraces: long roof runs and rear outriggers sit among neighbouring buildings, exactly the setting where NFRC warns of eddies and extra suction. HSE’s roof repair guidance for builders (CIS60) says terraced properties need scaffolding at the front and back.
- Tall chimney stacks: stacks stand above the ridge and take the full force of the wind. CIS60 calls for scaffolding around chimneys, and work on them is among the first to stop as gusts rise.
- Mansards and dormers: steep slated faces sit high up, where wind is stronger than at street level.
- Flat roofs on rear extensions and dormers: membranes, liquid coatings and insulation boards have the lowest limits in the NFRC guidance, so flat roofing work is more weather-sensitive than slating on the same day.
For general roof repairs, NFRC section 5.5 notes that the sequence of work may be dictated by the prevailing wind.
Frequently Asked Questions
What wind speed should you not work in on a roof?
Slating and tiling should stop when the mean wind speed reaches 23 mph or gusts reach 35 mph, according to NFRC guidance. Lightweight materials such as liquid coatings stop at 17 mph mean, gusting 26 mph.
Can roofers work in the wind?
Yes, roofers can work in light to moderate wind as long as readings at roof level stay below the limits for the task. The limits are lower for large, light materials such as underlay and insulation boards. Once gusts pass the figure for the job, work stops and the roof is made safe.
How much wind can a roof handle?
There is no single figure, because it depends on the roof's age, fixings and condition. The Financial Ombudsman Service notes that the Beaufort scale describes slight structural damage from 47 mph, and insurers treat gusts of 55 mph as storm conditions. When assessing a claim, insurers ask whether the wind was strong enough to damage an otherwise well-maintained property.
Is 20 mph too windy for roofers?
A 20 mph mean is below the 23 mph limit for slates and tiles but above the 17 mph point for felt rolls and liquid-applied systems. The gust figure matters just as much, because gusts can be 50 to 100 per cent higher than the mean.
Can roofers lay felt in windy conditions?
Roofers can lay felt in light wind, but NFRC says extreme care is needed with rolls of underlay from about 17 mph mean, gusting 26 mph. On flat roofs, reinforced bitumen membranes stop altogether at 23 mph mean, gusting 35 mph.
Do scaffolders work in high winds?
Scaffolders work to the limits set by the scaffold design and their risk assessment, as there is no fixed legal wind speed. HSE requires a scaffold to be checked whenever it is adversely affected, for example by high winds. Sheeting and netting add wind load, so they must be included in the design.
Who decides when it is too windy to work on my roof?
The roofing contractor decides, because the Work at Height Regulations 2005 make the employer responsible for stopping work when the weather jeopardises safety. NFRC guidance recommends that supervisors take wind readings at the place of work and keep a record of them. A homeowner should never be asked to overrule that call.
If you have roofing work planned or wind has already damaged your roof, JW Roofing Solutions is based in Balham SW12 and works across SouthWest London, including Balham, Clapham, Wandsworth, Streatham and Tooting. Call 07467 800002 or request a free written quote.
Need help with your roof? JW Roofing Solutions provides roofing services in SouthWest London. Get a free, no-obligation quote.




