How to Fix a Leaking Flat Roof: Find It, Patch It or Call a Roofer

Rain droplets beading on a dark flat roof surface, the starting point for how to fix a leaking flat roof

To fix a leaking flat roof, first find where the water actually gets in, which is usually a split joint, an upstand, an outlet or a rooflight edge rather than the middle of the roof. A small split can be patched on a dry day with primer and flashing tape; anything larger, or a soft deck, needs a roofer.

Most quick answers jump straight to a tin of sealant. That can stop a leak for a while, but a patch in the wrong place just moves the problem, and a patch on a worn-out roof buys very little time. This guide covers how to find the leak, the temporary and permanent fixes for felt, rubber (EPDM) and liquid-coated roofs, what repairs cost in 2026 and when patching is no longer worth it.

Key facts

If the roof is above ground floor, or you would rather not go up at all, our flat roofing service covers torch-on felt and liquid roofing across SouthWest London, and we trace leaks to their source before we quote.

What Should You Do First When a Flat Roof Is Leaking?

Orange bucket, mop and cloth ready to catch drips and protect the floor from a roof leak
Photo: BOOM Photography / Pexels

Protect the inside of the house first and leave the roof until the rain stops. Climbing onto a wet flat roof in the dark is how a small leak turns into an injury.

  • Put a bucket under the drip and towels or a dust sheet around it, and move furniture and rugs out of the way.
  • If water is near a light fitting or socket, switch that circuit off at the consumer unit and keep clear of it.
  • If a ceiling is bulging with water, keep people out from under it.
  • Take photos and short videos of the drip, the stain and the weather. They help a roofer find the leak and support any insurance claim.
  • Note when it leaks: only in heavy rain, only when the wind blows from one side, or after every shower. The timing points to the cause, as our guide to a roof leaking in heavy rain explains.

The HSE advises against going on any roof in rain, ice, frost or strong winds. Treat outside work as a job for the next dry day.

Where Do Flat Roofs Leak Most?

Aerial view of flat roofs in Luton showing parapets, upstands and rooftop details where leaks often start
Photo: Altaf Shah / Pexels

Flat roofs rarely leak through the middle of a sound covering. They leak where the covering stops, turns, joins or is pierced. The Department for Communities maintenance checklist names parapets, gutters and outlets, eaves and verges, fixings, rooflights, vents and flues, expansion joints and the roof surface as the places deterioration appears, and Skyguard Flat Roofing says most felt and EPDM roofs fail at the joins first.

WhereWhat to look forUsual fix
Upstands and wall abutmentsFelt pulled away from the wall, cracked flashing or render just above the roofRe-dress the upstand and renew the flashing
Outlets and guttersSilt, leaves or moss in the outlet, a lifted outlet collar, puddles round the drainClear the outlet; re-seal or renew the collar
Laps and jointsLifted or open seams, often at the low end of the roofClean, prime and patch over the joint
Rooflights, vents and pipesGaps or cracked sealant around the kerb or pipe collarRe-seal or re-flash the kerb or collar
Eaves and verge trimsFelt split along the edge trim, water marks on the fascia belowRenew the edge detail
Open roof surfaceSplits, cracks, blisters or crazingPatch small damage; larger areas need re-covering

Standing water makes every one of these worse, because it sits on the weak point for days. If puddles linger after rain, see our guide to ponding on a flat roof, and if the felt has bubbles, read about flat roof blistering.

How Do You Find a Leak in a Flat Roof?

Work from the inside out: map where the water appears, then check the nearest edge, outlet or opening uphill of it. Water runs along the deck and joists before it drips, so the hole is often not directly above the stain.

  1. Mark the wet patch on the ceiling and note which way the roof falls, towards the gutter or the outlet.
  2. If there is a hatch into the roof void, look with a torch for wet timber or insulation and follow the trail uphill.
  3. From a window, or from a ladder footed and tied at the edge, look at the outlets, the upstand against the house wall, any rooflight and the edge trims nearest the stain, without stepping onto the roof.
  4. Look for open laps, splits, cracked flashing above the upstand and blocked outlets, and photograph anything that looks wrong.
  5. On a dry day, a helper can run a hose gently over one small section at a time, starting at the lowest point, while someone watches inside. Move uphill only once a section has stayed dry.
  6. If you still cannot find it, a roofer can trace it. Some firms also offer electronic leak detection, which Less.co.uk puts at about £500 for the test and report, with the repair extra.

Do not walk across the roof to look. The HSE says all roofs should be treated as fragile until a competent person has confirmed otherwise, and rooflights are a particular danger because they can be hard to see. If you need to step onto the roof at all, read can you walk on a flat roof first.

How Do You Fix a Leaking Flat Roof? Temporary vs Permanent Fixes

A temporary fix stops the water until the weather allows a proper repair; a permanent fix replaces or properly overlaps the failed material. Most DIY products are temporary unless the damage is small and the roof around it is sound.

MethodBest forConditionsHow long it lasts
Emergency roof sealant (for example Thompson’s Emergency Roof Seal)Stopping an active leak on felt or asphaltCan go on in wet weather; not below 0°C or on frostTemporary; not for areas that are walked on
Self-adhesive flashing tape (for example Bostik Flashband)Small splits, open laps, cracked flashingsClean, dry surface from 5°C to 30°C, primed if porous or old feltMedium term on a sound roof; not for walked-on areas
EPDM repair patchPunctures and cuts in a rubber roofCleaned and primed membrane, dry conditionsPermanent if done to the maker’s method
Cut back and re-felt the damaged areaCracked or split felt over a dry deckDry deck, matching felt, a rooferPermanent
Re-cover the whole roof (felt or liquid system)Soft deck, leaks in several places, old feltA roofer; may need Building Regulations approvalPermanent

Thompson’s data sheet says its Emergency Roof Seal can be used in adverse weather and under ponding water, covers about 1 m² per litre and should be surface dry within 24 hours. That makes it useful on the night of a leak, as long as the roof can be reached safely. For felt that has cracked, the Department for Communities guidance recommends cutting back the existing felt, letting the area dry and laying a new layer of high-performance felt with a suitable overlap, which is the permanent version of the same repair.

How Do You Patch a Small Split in a Felt Flat Roof?

This is the one repair many homeowners can do safely: a small split on a ground-floor garage or extension roof, reached from a ladder at the edge, on a dry day above 5°C. These steps follow Bostik’s Flashband data sheet.

  1. Sweep off loose chippings, dirt and moss. Bostik says to remove moss and lichen with a fungicidal wash and let the surface dry.
  2. Make sure the area is completely dry. The tape will not bond to a wet surface.
  3. Fill any gaps or hollows deeper than 3mm with a suitable filler.
  4. Brush Flashband primer onto the area, generously on old felt so it soaks in, and let it dry. Tape over it the same day, as Bostik says not to leave primer more than 24 hours.
  5. Cut the tape to cover the split with a good margin, peel the backing as you go and press it down by hand. Where two lengths meet, overlap them by at least 25mm.
  6. Roll it firmly with a seam roller, especially along the edges and overlaps, to push out trapped air.

In cold weather Bostik recommends keeping the roll somewhere warm overnight and warming the surface, because the tape grips less in the cold. It also says Flashband should not be used where it will be walked on and must not touch silicone sealant, so any old silicone repair has to come off first. Tape on otherwise sound felt can be a good repair; tape over brittle, crazed felt is a stopgap, because the felt around it is failing too.

How Do You Fix a Leak in a Rubber (EPDM) Flat Roof?

Holes in EPDM are patched with EPDM, not with bitumen tape or sealant. ClassicBond’s installation guide says to repair mechanical damage with 225mm uncured flashing tape, keep the edge of the patch at least 75mm from the damage, clean the membrane, prime it with ClassicBond primer and roll the patch immediately.

Many rubber roof leaks are at details rather than holes: corners, upstands and places where the membrane has pulled away from an edge trim. Those need the membrane re-dressed and re-bonded, not a patch on top. If you are not sure what your roof is covered in, our EPDM vs GRP vs felt comparison shows how to tell them apart.

Not sure it is safe to go up? We trace flat roof leaks to their source and give written, itemised, no-obligation quotes, so you know whether a patch will do or the roof is near the end of its life. Get in touch and send a photo of the stain and the roof if you can.

When Is Patching a Leaking Flat Roof a Waste of Money?

When the roof itself is worn out. Less.co.uk’s survey of UK roofers found that a patch on a sound roof can last 3 to 7 years, but on an ageing roof it may last only 1 to 2 years. The same survey lists the signs that a new roof is the better buy:

  • cracking across much of the roof;
  • a soft, spongy or wet deck;
  • leaks coming back in different places;
  • a felt roof more than about 20 years old;
  • wet insulation or rotten timber.

Re-covering more than part of a roof can also bring in Building Regulations. Coventry City Council’s building control guidance explains that renovating more than 25% of a roof’s surface needs approval and may mean adding insulation, and it gives replacing the felt on a flat roof as an example. A roofer should tell you if this applies. Our flat roof repair guide compares repair and replacement costs in more detail.

How Much Does It Cost to Fix a Leaking Flat Roof in 2026?

Most single leaks cost a few hundred pounds to fix. These are the ranges UK roofers publish, collected by Less.co.uk in November 2026:

RepairTypical UK rangeMiddle price
Patch on a felt roof (split, blister or small hole)£150 to £450About £280
Repair to a rubber (EPDM) roof£200 to £400About £300
Repair to a fibreglass (GRP) roof£225 to £525About £375
Finding and fixing a leak£150 to £500 (up to about £750 for a hidden leak)About £325
Flashing or upstand repair£200 to £500About £375
Blocked or leaking outlet£120 to £450Not given
Emergency make-safe (temporary cover only)£150 to £400About £275

For comparison, BestBuilders’ 2026 guide puts re-felting a small flat roof such as a garage or extension at £1,000 to £2,500. Less.co.uk notes that London firms tend to charge more and that a tower for a first-floor roof adds about £150 to £300. These are published UK ranges, not our prices; we quote each job in writing after seeing it.

Who Is Responsible for a Leaking Flat Roof in a Flat?

Row of white stucco London terraced houses, many split into flats where the freeholder repairs the roof
Photo: Lajos Kristóf Kántor / Pexels

If you own a leasehold flat, the roof is usually the freeholder’s responsibility, not yours. The Leasehold Advisory Service says the landlord is usually responsible for the roof, the external walls and communal areas, and recovers the cost from leaseholders through the service charge.

Its water leaks guidance adds that leaks caused by the structure, such as a leaking roof, are usually the landlord’s to fix, but your lease decides, so check it. Report the leak to the freeholder or managing agent in writing, with photos, as soon as you notice it. LEASE also explains that the landlord must consult leaseholders if a repair will cost any one leaseholder more than £250. In a leasehold house you are usually responsible for the roof yourself. Many Victorian and Edwardian houses in SouthWest London are split into flats, and the flat roof over a back addition can sit above one flat while still belonging to the freeholder.

Does House Insurance Cover Flat Roof Leaks?

Sometimes, if a storm caused sudden damage; rarely if the roof simply wore out. The Financial Ombudsman Service says it is unlikely to uphold a flat roof storm claim if the roof was already in bad condition, the storm only highlighted an existing problem, or the damage was gradual or wear and tear. Photos taken at the time and a roofer’s written report help either way.

Should You Fix a Flat Roof Leak Yourself or Call a Roofer?

DIY is reasonable for a small, visible split on a ground-floor garage or extension roof that you can reach safely from the edge, on a dry day. A roofer is the better choice when any of these apply:

  • the roof is above ground floor, or you would need to stand on it;
  • the leak is at an upstand, wall abutment, rooflight or outlet;
  • you cannot find the leak, or it comes back after a patch;
  • the deck feels soft or bounces underfoot;
  • the felt is cracked all over or more than about 20 years old.

What we would do: on a sound roof with one clear defect, repair that defect properly and leave the rest alone. On an old felt roof that has already been patched more than once, we would rather tell you honestly that re-covering is the better use of your money than sell you another patch. If a repair will do the job, we will say so.

Flat roof repairs depend on the weather more than most roofing jobs. Our guide on whether roofers can work in the rain sets out which materials need a dry deck and how long after rain work can start.

Frequently Asked Questions

Can you fix a leaking flat roof from the inside?
Not permanently. You can catch the water and protect ceilings and floors from inside, but the waterproof layer is on top of the roof, so the real repair has to be done outside once it is dry and safe.

What is the best sealant for a flat roof leak?
It depends on the covering. Bitumen-based emergency sealants and flashing tape suit felt and asphalt roofs, while rubber (EPDM) roofs need EPDM primer and patches. Do not use silicone on felt: Bostik says Flashband must not touch silicone sealant.

Can you repair a flat roof in the rain?
Only as a temporary measure. Some emergency sealants can be applied in the wet, but the HSE advises against going on any roof in rain, so proper repairs should wait for a dry day.

How long does a flat roof patch last?
Less.co.uk’s 2026 survey of UK roofers found a patch on a sound roof can last 3 to 7 years. On an ageing roof it may last only 1 to 2 years, which is when re-covering usually makes more sense.

Why is my flat roof leaking when I cannot see a hole?
Most flat roof leaks are at details such as upstands, laps, outlets and rooflights rather than the open surface. Water can also run along the deck before it drips, so the stain may be some distance from the defect.

Who pays to fix a leaking flat roof above a leasehold flat?
Usually the freeholder, who recovers the cost through the service charge, but your lease decides. Report the leak in writing with photos as soon as you notice it.

Flat Roof Leak Repairs in SouthWest London

JW Roofing Solutions repairs leaking flat roofs across SouthWest London, including Balham, Clapham, Wandsworth, Streatham and Tooting. We trace the leak to its source, give honest advice on whether a repair will do, and leave the site clean and tidy. Our team has over 40 years of combined experience and we are fully insured. Call +44 7467 800002, get in touch online or read more about our flat roofing.

Need a roofer in SouthWest London?

Get straightforward advice and a clear, written quote with no obligation. Over 40 years of combined experience across our team.